10 Quick Tips About Fiat Panda Key Fob Replacement
Reasons Your Fiat 500 Key Fob Won't Work
A key fob from Fiat 500 makes it simple to open doors and start your car. There are a variety of reasons why the fob could stop working. These include a dead battery, damage to the receiver module, issues, and interference.
This listing is for a NEW replacement Fiat Flip Key Remote - look-alike Ilco brand that must be professionally programmed by a local locksmith (click here to search for a Locksmith Search). This remote includes lock, unlock and trunk buttons.
Dead Coin Battery

A dead battery is the most frequent cause of your 500 key fob not functioning. Key fobs of today have only a limited range of operation and must be within a few inches of your vehicle in order to work. If you are far from your vehicle and you press the key fob button the car will not respond, and will display an "Key Fob Not Detected" message in the instrument cluster.
If this occurs then replace the battery for your coin-cell (Part Number CR2032) with a new battery from a reputable brand such as Panasonic Duracell or Energizer. You can typically find them at your local hardware store or on the internet.
After you've replaced the battery in the coin cell You can test it by standing close to your Fiat 500 and pressing the buttons. The car should blink its parking lights and the key fob should be able to operate the lock and unlock switches.
If the fob's key doesn't work after replacing the battery, it may be damaged by water that blocks it from connecting to the receiver module in your car. Water damage can happen in a variety of ways, ranging from small splashes to submerging the fob salt water at the beach. If you suspect that your fob was exposed to water, you can place it in a bag of rice to draw out the moisture. If that doesn't work, your fob will probably need to be reprogrammed by a professional auto locksmith or the dealer.
Water Damage
Although the fob is equipped with rubber seals that keep water from the chip's electronic circuit the device, submerging it into the ocean or washing it in a machine could cause water damage. Saltwater is particularly dangerous to the fob's circuit board, causing it to short out and eventually die. It's not good to soak the fob in water but don't give up in the event that you accidentally drop it in the water or don't take it out of your pants pocket.
Remove G28 Car Keys . Before replacing the battery clean the electronic chip with isopropyl or a similar product. Then try the fob and test if it works. If the fob doesn't work then it might need to be changed. This is usually handled by a professional or dealer auto locksmith.
If your key is old and is not programmed for your car then you'll need to replace it completely. This is an easy process which can be accomplished by a professional locksmith for automotive use. The locksmith needs to cut the key to match the ignition in your vehicle. They will also need to reprogram the fob to your vehicle's system. This is a quick and inexpensive process which can be completed in the same day.
Receiver Module Issues
Your 500 key fob may stop working because it is out of range. The remote has a maximum range of 30 feet, which means if you are too far away from your vehicle, it won't respond to your commands. This can be fixed by moving closer to your vehicle until it starts responding.
If you've replaced your coin battery (commonly known as"button" or "button" or "watch") and the fob isn't working, it could have an internal circuit board problem. Reprogramming the fob is usually the solution to this problem. You can find directions on how to do this for most vehicles by searching YouTube or reading the owner's manual.
You may need to replace the metal retaining clips that hold the battery of your coin in place. If they lose tension it may prevent your battery from sitting properly and cause your remote to malfunction.
In rare cases the fob might be out of connection with your vehicle as a result of software or hardware problems. It is possible to fix this issue by visiting your local auto-locksmith or dealer to reprogram your key fob. In some instances, the software may also require reinstallation in your body control modules.
Interference
Interference can also cause the key fob not to receive or transmit a signal. This could happen if the key fob is located near an electronic radio transmitter (cell phones or radar detectors) or another source of electromagnetic radiation. The key fob might not function due to a bad connection with the buttons or water damage, or damage to the internal chips.
If the key fob failed to work one day without notice or after trying every option at home to fix it e.g. You could have a malfunctioning 500 receiver module in the event that you've tried replacing the battery, reprogramming or using a spare key fob. The receiver module, which is located under the dashboard, detects radio frequency signals from your key fob. It converts them into electronic commands that the vehicle interprets.
Fortunately, there's an easy method of resetting all of the on-board systems in your 500 and include the key fob. Disconnect the battery for 15 minutes by taking off first the negative cable, then the positive cable. Reconnect the battery. This will eliminate any remaining electrical charge, and then restart the computer in your car. This will help you get your key fob to work again. If the issue persists you should seek out an experienced technician. They will be able to diagnose the exact cause of your problem.